DEATH OR SERIOUS INJURY may result if personnel fail to observe safety precautions.Work on electronic equipment should not be undertaken unless the individual(s) have been trained in the proper maintenance of equipment and is (are) familiar with its potential hazards. HIGH VOLTAGE Is used in the operation of this equipment. If there is any question in the mind of operating/ service personnel as to the applicability of these documents, then, prior to working on the equipment, they should verify with the owner, whether the equipment has been modied and if the current literature is available. It is the responsibility of operating/service personnel as to the applicability of these documents to the equipment in question.
#York ycal high ambient kit update#
While YORK makes no commitment to update or provide current information automatically to the manual user, that information, if applicable, can be obtained by contacting the nearest YORK Engineered Systems Service ofce. MODELS YCAV0569, 0639, 0679, 0719, 0739, 0819, 0889 and YCAV0969 STYLE "A"ĬHANGEABILITY OF THIS DOCUMENTIn complying with YORK's policy for continuous improvement, the information contained in this document is subjected to change without notice. NOTE is used to highlight additional information which may be helpful to you.AIR-COOLED SCREW LIQUID CHILLERSRENEWAL PARTSNew Release Form: 201.21-RP2 (605) WARNING indicates a potentially haz ard ous sit u a tion which, if not avoided, could result in death or serious injury. Usually an instruction will be given, together with a brief explanation. SAFETY SYMBOLS The following symbols are used in this document to alert the reader to areas of potential hazard: DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.ĬAUTION identifies a hazard which could lead to damage to the machine, damage to other equipment and/or en vi ron men tal pollution. This individual shall also be familiar with and comply with all applicable governmental standards and regulations pertaining to the task in question. It is essential that, prior to performing any task on this equipment, this individual shall have read and understood this document and any referenced materials. It is expected that this individual possesses independent training that will enable them to perform their assigned tasks properly and safely. This document is intended for use by owner-authorized operating/service personnel. Which it is situated, as well as severe personal injury or death to themselves and people at the site.
Failure to comply with any of these requirements could result in serious damage to the equipment and the property in It is the obligation and responsibility of operating/service personnel to identify and recognize these inherent hazards, protect themselves, and proceed safely in completing their tasks. Each of these items has the potential, if misused or handled improperly, to cause bodily injury or death. During installation, operation, maintenance or service, individuals may be exposed to certain components or conditions including, but not limited to: refrigerants, oils, materials under pressure, rotating components, and both high and low voltage. READ BEFORE PROCEEDING! GENERAL SAFETY GUIDELINES This equipment is a relatively complicated apparatus. Web address for the Revision Sheet 035-XXXXX-XXX 2
YORK part number for the Revision Sheet to aid manufacturing and distribution If necessary it will refer the reader to an additional supplement or bulletin. The Description/Change will explain the change. Revision Sheets are available for the IOM and Renewal PartsĮach update will be assigned a sequential Rev. It is the responsibility of installing/operating/service personnel to determine prior to working on the equipment, that they have all of the applicable literature, that it is current and that the equipment has not been modified since manufacture. If not found with the manual, the current Revision Sheet containing any applicable revisions, and the manual, can be found on the internet at The Renewal Parts (RP) manual and revision sheet for this equipment can also be found at this internet site. Literature updates that may occur will be printed on the Revision Sheet and included with the Installation, Operation & Maintenance (IOM) man, which is provided with new equipment. (STANDARD, BRINE & METRIC MODELS COMBINED)ĬHANGEABILITY OF THIS DOCUMENT In complying with YORK’s policy for continuous product improvement, the information contained in this document is subject to change without notice. YCAS AIR-COOLED LIQUID CHILLERS YCAS0130 THROUGH YCAS0230 STYLE G AIR-COOLED SCREW LIQUID CHILLERS INSTALLATION, OPERATION & MAINTENANCE
0 kommentar(er)
